Results 1 to 14 of 14

Thread: Dexcool vs. other coolants

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Feb 2009
    Location
    Nevada
    Posts
    26

    Default Dexcool vs. other coolants

    I am still hearing Duramax owners discussing the Dexcool issue. I know GM insists it must be used. Is there any definitive information as to the advantages/disadvantages of changing from Dexcool to another brand of coolant/antifreeze? I am aware of previous lawsuits etc., but by now there must be expert guidance on this question. THANKS!

  2. #2
    Join Date
    Jan 2001
    Location
    New Hampshire - Live Free or Die
    Posts
    6,057

    Default

    15 years, no problems....
    The Constitution needs to be re-read, not re-written!

    If you can't handle Dr. Seuss, how will you handle real life?

    Current oil burners: MB GLK250 BlueTEC, John Deere X758
    New ride: MB GLS450 - most stately
    Gone but not forgotten: '87 F350 7.3, '93 C2500 6.5, '95 K2500 6.5, '06 K2500HD 6.6, '90 MB 350SDL, Kubota 7510

  3. #3
    Join Date
    Jan 2005
    Location
    Southern Indiana
    Posts
    1,177

    Default

    I've been putting it in them since they came out and have never had an issue.

  4. #4
    Join Date
    Mar 2000
    Location
    Loyal WI US
    Posts
    10,792

    Default

    The Dex Cool lawsuits in my opinion stem from GM's (Chev in particular) inability to seal an intake gasket to save their own lives. Now that the newest engines don't have coolant in the intake this seems to have pretty much stopped. Nothing changed, just the abscence of air from leaky gaskets.

    The 6.5 used Dex Cool for many years also and I have never seen a lick of corrosive evidence except again for where it would leak ie: heater feed nipple on water crossover. I did make the mistake of leaving coolant between the upper rad hose and stat housing and this pitted the housing pretty bad outward of the clamp.
    Kennedy Diesel-owner
    More than just a salesman-I use and test the products that I sell on a daily basis!
    Superflow Lie Detector in house
    2002 Chev K2500HD D/A CC Long LT 11.77@ 124mph at 7700# fuel only-e.t. needs help
    2005 Chev K3500SRW D/A CC Long LT(SOLD)
    2007 Chev K2500 Classic EC Short LT (Sold)
    2012 GMC K3500SRW D/A CC Long LTZ Happy Birthday to me! Built 1 working day after my birthday and delivered 7 days later.
    2016 GMC K3500SRW D/A CC short LTZ

    Custom tuning in house using EFI Live tuning software!

  5. #5
    Join Date
    Jan 2005
    Location
    Southern Indiana
    Posts
    1,177

    Default

    ditto to what john said. for a while there GM might as well have not even used gaskets on lower intake manifolds,, they probably would have leaked less. Since that happened about the time dexcool was put in everything, it got the blame.

  6. #6
    Join Date
    Feb 2000
    Location
    Montana
    Posts
    11,382

    Arrow Texaco/Havoline Dex-Cool - reprint from 2003

    Texaco/Havoline Dex-Cool
    By TheDieselPage.com - 2003

    GM made the switch to the new orange-colored Texaco/Havoline Dex-Cool in the 1996 model year due to its longer service cycle, longer water pump seal life, high temperature aluminum protection, and a higher coefficient of heat transfer. At the time of introduction, this new coolant came with a recommended 100,000 mile maintenance cycle. Shortly thereafter, GM began recommending a 5 year/150,000 mile coolant maintenance cycle for the 6.5L (and Duramax 6600) turbo diesel engines because of the improved long-life characteristics offered by this new coolant. According to a 1998 NARSA (National Automotive Radiator Service Association) report, Texaco/Havoline began recommending the average cycle life of this new silicate-free orange coolant be increased to 250,000 miles and beyond in other applications.

    DEXCOOL is a registered trademark of General Motors Corporation, used under license by Texaco Lubricants NA. Dex-Cool contains an ethylene glycol base along with carboxylate corrosion inhibitors (organic acid) for an advertised improvement in rust and corrosion protection. For more information about Dex-Cool, you can call 1-800-782-7852 or visit www.Havoline.com on the web.

    Conventional coolant, such as Prestone brand antifreeze/coolant shown above (green dye) is also an ethylene glycol based coolant, but uses a blend of silicate corrosion inhibitors. Green-dyed silicated coolants represent the type of formulation used by GM prior to the introduction of Dex-Cool. For continued cooling system protection, Prestone recommends an annual flush and fill when using a silicated ethylene glycol coolant. This is necessary because the concentration of conventional rust and corrosion inhibitors (silicates) tend to decrease over time. Prestone also produces a silicate-free organic-acid based coolant, but we have no experience with this product. For more information about Prestone brand automotive coolants, you can visit them on the web at www.Prestone.com.

    GM does not recommend installing an organic-acid based coolant in systems with a copper/brass/soldered radiator because of a potential for lead corrosion. However, Prestone says their organic-acid ethylene glycol tests have shown no problem with lead corrosion, and recommends the use of their organic-acid ethylene glycol coolant in either copper/brass or aluminum systems. Our tests here at The Diesel Page with Texaco/Havoline Dex-Cool and copper/brass/soldered radiators have shown no internal cooling system deterioration after nearly 120,000 miles and four years of use (6.5TD).

    Converting a system containing silicated coolant (yellow/green dye) to an organic-acid coolant (orange dye) requires a thorough system flush to remove all traces of the original silicated ethylene glycol coolant. These two coolants are somewhat compatible, in that you won't damage your engine or cooling system with a mix, but mixing coolants containing carboxylate and silicate corrosion inhibitors will shorten the service cycle to that of silicated ethylene glycol. Copyright 2003 by The Diesel Page

    While Texaco/Havoline recommends a "good quality tap water" when preparing a 50% Dex-Cool solution, both NARSA and The Diesel Page recommend using distilled water to dilute Dex-Cool. Chlorinated or hard water can affect the long-life properties and corrosion protection offered by any automotive coolant.

    However, mixing two unrelated formulations of organic-acid ethylene glycol coolants is a concern. There are several different chemistries used for long-life coolant that can appear as pink or orange or red. They may not be compatible with one another. Europe has their own formulation, Japan has theirs, Chrysler Corporation has theirs, and Texaco/Havoline has theirs. If someone topped off a 6.5 or Duramax cooling system with a non-compatible coolant, undesirable consequences could result. If in doubt, look for a description on the bottle indicating that it meets specification GM-6277M or ASTM D-3306. I always carry a gallon of pre-mixed Texaco/Havoline Dex-Cool (with 50% distilled water) with me whenever I travel, to help mitigate this possibility.

    We have learned that an air/coolant interface within the engine or cooling system could create an environment for aluminum or iron corrosion when using Dex-Cool. Not coincidentally, GM incorporated an air-bleed screw in the 6.5L & Duramax 6600 thermostat housing. This provides a means to vent air from the cooling system. Additionally, the coolant surge tank is also designed to remove air from the cooling system. So, unless there is some sort of engine or cooling system failure (or inadequate initial fill), there should never be an air/coolant interface in your 6.5 or Duramax cooling system.

    A recent class-action suit has been brought against GM for cooling system corrosion involving 4.3L engines used in GM's late model Blazer, Jimmy, Olds Bravada, Sonoma, and S10 pickups. As reported in the May 22, 2003 issue of The Columbus Dispatch, GM stated that it "is aware of concerns about Dex-Cool. However, those problems involve customers who ran their cooling systems for an "extended period of time" -- 15,000-20,000 miles - with low coolant levels." GM went on to say that "There are 35 million to 40 million GM vehicles on the road that use Dex-Cool, and the overwhelming majority have experienced no problems with the cooling system." As stated earlier, we have also identified a problem with a coolant/air interface, and the potential for corrosion as a result. We also know that cooling system performance (when properly filled with a 50% Dex-Cool/distilled water solution) will surpass those using a green silicated ethylene glycol coolant.

    As a result of this class-action suit, some owners of the GM full-size diesel pickup engines have become concerned about the possibility of cooling system corrosion in their own vehicles. Ensuring the absence of air in your cooling system should preclude any sort of corrosion problem. If you notice the coolant surge tank level rising or falling beyond the hot/cold levels, you may need to investigate the cause. An external coolant leak, a faulty cooling system pressure cap, a leaking head gasket or some other sort of failure could cause an air/coolant interface to develop inside your engine. This is a bad thing.

    Some have suggested draining the Dex-Cool and refilling with a green ethylene glycol coolant. Before taking that step, consider this: This radiator core image illustrates the result of improper cooling system maintenance after the vehicle accumulated just 135,000 miles. Perhaps more importantly, it also shows what the combination of improper maintenance and green silicated ethylene glycol can produce.

    Human nature being what it is, too many people will neglect certain systems in their vehicle. The radiator shown here, the engine and the cooling system were replaced soon after that photo was taken in 1998, and the new cooling system and 6.5TD engine have subsequently accumulated 120,000 miles on a single initial fill of Texaco/Havoline Dex-Cool (& 50% distilled water). The internal condition of the radiator and thermostat housing still appear like new. If the Dex-Cool filled systems survive better when neglected, that's a good case all on its own to use Dex.

    Some have blamed cylinder head gasket failures on Dex-Cool. However, here at The Diesel Page, we know that the primary problem with 6.5 head gaskets is directly related to the factory 21.5:1 compression ratio. During the 2001 Rendezvous in Ohio, Matt Koning, CEO of Peninsular Diesel told our group during a seminar that Peninsular had never replaced a failed head gasket on any of their 18:1 compression ratio marine 6.5L engines - not a single one in 10 years of 6.5 marine engine production. In contrast, head gasket replacement for the "on-road" 6.5TD engines (with their 21.5:1 compression ratio) is a somewhat routine occurrence between 80,000 and 200,000 miles.

    There is no discernable difference in 6.5 head gasket reliability for engines built prior to or since the introduction of Texaco/Havoline Dex-Cool. If Dex-Cool created an endemic cooling system corrosion problem with the 6.5 and Duramax engines, The Diesel Page would be well versed in the science and chemistry behind it (by the shear volume of routine email messages and phone calls). Since The Diesel Page began in early 1996, a question about coolant type has not been an issue we've dealt with till this article.

    Continued next post:

    Copyright 2003 by TheDieselPage.com
    Last edited by More Power; 01-13-2011 at 14:13.

  7. #7

    Default

    There is nothing wrong with Dexcool coolant,the issue first arose with head gasket leaks,the molecules are smaller and will leak whereas the traditional green coolant will not.
    Manufactures had to redesign head gaskets and head/engine block finishes to prevent leakage.
    They have finally corrected it for the most part.
    CC
    2008 GMC 3500HD SLT SRW CC D/A 4X4 Loaded
    Nav,Rear DvD,Sunroof,Etc.

  8. #8
    Join Date
    Feb 2000
    Location
    Montana
    Posts
    11,382

    Arrow

    Quote Originally Posted by Canadian Cowboy View Post
    There is nothing wrong with Dexcool coolant,the issue first arose with head gasket leaks,the molecules are smaller and will leak whereas the traditional green coolant will not.
    Manufactures had to redesign head gaskets and head/engine block finishes to prevent leakage.
    They have finally corrected it for the most part.
    CC
    The traditional green dyed coolant and the newer Dex-Cool are both formulated using an ethylene glycol base. Aside from the dye color, the difference is really more about the corrosion inhibitors. Dex-Cool uses carboxylate corrosion inhibitors and green dyed coolant uses silicate corrosion inhibitors. I don't know about molecule size for the corrosion inhibitors, but ethylene glycol is ethylene glycol and water is water (in these 50/50 mix ratios).

    Aside from metal(s) deterioration related to coolant, gasket deterioration is also something to consider. I saw a lot of it in the late 1980s through the 1990s with the 6.2/6.5 diesels that were equipped with the green coolant. Head gaskets for the 6.2/6.5 have definitely improved through the years and for a variety of reasons, but it's the water pump gaskets and other wet gaskets that I saw deteriorate (that had the green coolant) back in the day. I just don't see it with Dex-Cool.
    Jim

  9. #9
    Join Date
    Apr 2014
    Location
    Massillon Ohio USA
    Posts
    2

    Default DexCool in Detroit 8.2L Fuel Pincher

    I'm very happy to have found this forum. Perhaps I can finally get some answers or at least advice.

    I have a vintage 1972 Newell motorhome which was repowered in 1981 with a Detroit 8.2L Fuel Pincher turbo diesel. This is my first diesel engine. As of today this 33 year old engine has about 60,000 miles on it. I've done some research on this engine and it is known for blowing head gaskets. This would be really unfortunate since in the last year I haven't been able to find anyone with the tools to set the mechanical injector heights should we have to pull a head. Many other forums get nasty to people who have questions about this engine so I politely ask that I not be told to dump this engine in a lake....it runs great, has low mileage and with proper care I expect it to continue running for my lifetime since I can't see putting another 50k on a motorhome.

    When I purchased it last year it had some very old coolant in it. Everything was rusty so we flushed it and put in some of the pink Diesel coolant we got from Advance Auto Parts. Shortly thereafter the radiator sprung a leak so I had it re-cored, changed all the hoses, new thermostats, flushed and refilled the cooling system with new coolant (again the pink stuff).

    I have years of experience using DexCool in my vintage gasoline engines and LOVE it. I change it every 4 years and my cooling systems look like new. I've never discovered any corrosion issues when using DexCool. I'd like to use it in my Detroit, but any Diesel mechanic I talk to (besides telling me to change engines) says to use the pink stuff. I'm not convinced that this coolant is anything but expensive window cleaning solution and I'm worried that additional corrosion will compromise the head gaskets in my engine.

    I've contacted Detroit and they sent me to Diamler who in turn sent me to MTU who in turn sent me back to Diamler who said they don't have any engineers left familiar with the 8.2.

    Does anyone know if I can I use DexCool as a coolant in my Detroit? What are the risks?

    Thank you very much!

    Bob Kopicki
    1972 Newell Motorhome with 1981 Detroit 8.2L Turbo
    1976 GMC C1500
    1967 Triumph TR-4a

  10. #10
    Join Date
    Feb 2000
    Location
    Montana
    Posts
    11,382

    Arrow

    Quote Originally Posted by sopicki View Post
    I'm very happy to have found this forum. Perhaps I can finally get some answers or at least advice.

    ...clip....

    Does anyone know if I can I use DexCool as a coolant in my Detroit? What are the risks?

    Thank you very much!

    Bob Kopicki
    1972 Newell Motorhome with 1981 Detroit 8.2L Turbo
    1976 GMC C1500
    1967 Triumph TR-4a
    Welcome to The Diesel Page.

    Owners of older engines, any engines, can expect to replace some or most of the gaskets due to age and the interaction between the coolants available decades ago and the gasket materials in use during that time.

    One of the more notable advancements in engine technology over time is the quality of materials and design of gaskets - both cooling system gaskets and especially head gaskets. We saw this in the 6.2L/6.5L GM diesel engines. Head gasket failures were common during the first 10 years of production - failures in preventing both coolant and compression/combustion leaks (head gaskets). The situation is far-far better now.

    I've successfully used Dex-Cool in engines that were originally supplied with the green coolant. Our 6.5L diesel project truck experienced no cooling system problems in more than 250,000 miles - without a routine cooling system flush or any other cooling system service. The water pump seals in this engine never leaked, and lasted beyond the 250K. We sold the truck, and eventually lost contact with its service history.

    The key to this success was likely due to the fact that a new copper/brass radiator was installed, and the engine was rebuilt using all current tech gaskets. The original heater core was flushed and all new hoses and clamps were added during the final assembly. Then, a 50/50 mix of Dex-Cool and distilled water was added. So, Dex should work for you.

    Unrelated to coolant, the Detroit 8.2L is said to employ just 4 head bolts per cylinder, where most current diesels have 5-6. The high compression and combustion pressures inherent in a diesel engine put more stress on head gaskets than do gas engines. Four bolts per cylinder can be marginal in containing these pressures. Depending on fueling, a turbocharger can add even more stress. Current head gaskets should improve durability, and new head bolts and/or head studs should be installed whenever the head(s) come off. I'd not reuse the old bolts/studs.

    Jim
    Last edited by More Power; 04-09-2014 at 10:22.

  11. #11
    Join Date
    Apr 2014
    Location
    Massillon Ohio USA
    Posts
    2

    Default

    Jim,

    I realize I'm probably in the wrong topic for this thread, but I found it using a search for DexCool and diesel engines.

    Thank you for your reply. I've been debating making a routine out of re-torqueing the head bolts to make sure the proper pressure is applied to the head and sealing gaskets. I've run this by a few diesel mechanics and they emphatically say NO - DONT DO IT! If it ain't broke don't fix it, but I worry about the bolts stretching.....and it does have a turbo.

    The problem I face right now is if a head gasket does let loose I don't have the injector height tool used to set the injectors. I've searched the internet and old diesel shops but can't locate one. Once a head gasket is replaced the injectors need to be re-set and that can't be done without the height setting tool.

    I've not been able to get anything back from Detroit, but I'm still working on finding an engineer who worked on the design and support for this engine.

    Thanks again,
    Bob Kopicki
    Massillon OH
    1972 Newell Motorhome repowered
    with 1981 Detroit 8.2L Fuel Pincher Turbo Diesel

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •