Results 1 to 8 of 8

Thread: 6.5 Engine Swap-1994 to 1995-Any Hidden Problems?

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1

    Default 6.5 Engine Swap-1994 to 1995-Any Hidden Problems?

    Hello,
    I am planning to swap engines this weekend. Before I do, I thought it a good idea to check with all of you. I have a 1994 engine that I am putting in a 1995 truck. The replacement engine is complete, including turbo, manifolds, wiring harness & computer. Are there any compatability issues that I need to be aware of before I start? My thoughts were to install the engine using the attached wiring harness, to prevent mis-wiring and save some time, but the old computer so that it matches the truck. Will the '94 injector pump work correctly with the '95 computer? If I have to use the '94 computer, will the transmission be affected? Also, I have read a little about these engines having to "re-learn" TDC. Will this be an issue, since the inj pump and crank have not been separated? Any tricks or tips to make the job easier?
    Thanks, Mike.

  2. #2
    Join Date
    Sep 2001
    Location
    Lubbock TX, USA
    Posts
    4,194

    Default

    The 94 and 95 engines are almost identical, wiring should be exactly the same on the engine. You can leave the injection pump wiring harness in the V of the engine and just plug them into the existing truck harness.

    Are both of the engines the same, S or F 6.5? If they're both Vin F engines (hd non egr version) then it should be a smooth transition.

    What is the truck?

    You might run into trouble if the 94 engine has a 5068 or 5067 IP on it, any other model IP won't give problems.
    1982 C10 SCSWB 6.5TD, mods too extensive to list. (13.69 1/4 mile @94.6 MPH) RACE TRUCK
    1982 C10 SCSWB 6.2NA, 2.73 700
    1986 C10 SCLWB 6.2TD 3.73 700
    1989 V20 SUB 6.2NA, 3.73 400
    1994 G20 VAN 6.5NA, 3.42 60E
    1994 K20LD ECSWB 6.5TD, 3.42 80E
    1995 K20 SUB 6.5TD, Wrecked, ran into by stupid teen.
    1995 C3500HD DRW 6.5TD, 12' Flatbed 5.13 80E
    1995 C3500HD DRW 6.5TD, 18' Rollback Wrecker 4.63 80E
    1994 C20HD ECLWB 6.5TD 3.73 80E Wifes Truck.
    1995 C20LD ECSWB 6.5TD 3.73 80E
    1995 K20LD SCLWB 6.5TD 3.73 80E
    1996 K30 DRW 6.5TD 4.10 80E
    1997 C10 Tahoe 2Door 2WD 5.7L to 6.5 Conversion Underway

  3. #3

    Default

    The truck is a GMC 3500 crew cab dually, with the "F" code engine. I am not sure of the VIN code on the '94 engine, but it does have an EGR valve under the plastic top trim. The inj pump has a sticker under the metal tag that reads "5521 11/06/00".

  4. #4
    Join Date
    Sep 2001
    Location
    Lubbock TX, USA
    Posts
    4,194

    Default

    Uh oh, You're swapping in a LD 6.5 into a truck that had an HD 6.5 in it.

    It will work, you'll need to swap intake manifolds for sure. The 5521 pump will be compatible with your '95.

    The main difference in engines at this point is internal, slightly different heads, containing smaller pre-cumbustion ports.

    Everything else should work on the '94 engine.

  5. #5

    Default

    Thanks, I appreciate the info. I had figured on changing at least the upper intake plenum to eliminate the EGR valve, so whats a few more bolts. Just makes the swap a little slower! Compatability with the pump was my main concern, so not having to swap them is a big relief. Since the pump & crank sensor haven't been separated, will I have to deal with the TDC "re-learn" process? Or does separating the engine from the computer require this?
    Mike.

  6. #6
    Join Date
    May 2000
    Location
    Little Neck,NY,USA
    Posts
    574

    Default

    Yes, You need to do the TDC Relearn because the computer has not been matched to the donor engine. The relearn should be done whenever you take apart the front of the engine, including when just replacing the crank sensor or swapping an engine, it does not need to be done when you do just an injection pump.
    Speaking of crank sensor, since you have the engine out, I would strongly recommend that you replace the crank sensor as a preventive measure. The 96' and up engines needs to have the power steering pump moved to replace the crank sensor, I am not sure how much room is behind the 94-95 p/s pumps.
    Just to clarify on the intake manifold, you need to replace both halves, the upper and the lower to remove the EGR system.
    William

    97 Chevy Tahoe 2Dr 6.5 Kennedy Exhaust Pipes w/Homemade Resonator and Flowmaster Muffler, Turbo Tech intercooler and Kennedy/Westers computer
    01 Sunline 2363 Travel Trailer

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •